1000/2000 /3000 Progressive Systems Metering Devices

Short Description:

Use For Progressive Lubrication System(PRG)
Progressive lubrication systems consist of a lubricator, progressive distributors, pipeline accessories and controllers. Features include: accurate metering of volume depending on piston diameter and stroke, easy installation, adjustment and maintenance. The PRG system is widely used in mining, steel mills, metallurgy, vehicles, harbors, construction machinery and other industries. The lubricant used is from NLGI-000 toNLGI-2, while system pressure ranges from 20 to 45Mpa. The filter element is 150μ.The progressive distributor is divided into two kinds of distributors: a center progressive distributor and a model progressive distributor. There is a choice of segment combinations, effectively ranging from periodic to near continuous lubrication.
Advantages: Precise discharge – All points can be fed and monitor individually – Trouble free installation – Easily pinpoints system issues


Product Detail

Product Tags

1- The 1000/2000/3000 series distributors distribute and proportion incoming oil or grease to bearing points. A typical 100 distributor consists of an inlet section, three to nine valves and an end section. One assembly can serve up to a maximum of 18 lubrication points.
2- The 1000/2000/3000 Series distributors have a sliding discharge piston and built-in outlet check valves. Blocks are offered in three output sizes. The discharge capacity of a block is determined by varying the piston diameter in the valve block. Valve blocks have two outlets located at each end of the assembly (double outlet blocks). They supply rated discharge outputs from each of the two outlets during one complete valve cycle. 
3- 1000 progressive grease distributor is an advanced design and reasonable structural oil distributor; Can be used in high pressure and wide temperature change conditions. It can be combined with electric and pneumatic pumps to form a single line lubrication system. It is used as a female distributor for various large machine tools and port of equipment , or for large single-line lubrication systems.

4- A standard set of dispensers consists of a “firt chip”✚a piece of “tail chip” ✚ 3-10 piece. It can provides 3-20 lubrication points for lubrication. Double outlet working chip, (after size use T to indicate the double outlet), there are two oil outlets, at the two ends of the working chip;

5- Note that for the double outlet working chip, can not Block any oil outlet, which will affect its normal operation and damage the distributor . Single grease outlet working chip (after the specification value of ,use S to indicate the single grease outlet), there is an oil outlet, which can be any of end of the working piece, and the other end of the outlet oil needs to be blocked.

1000 Metering Devices

Working chips  Standard flow ML/CYC Each chip outlet quantity  
1000-05T 0.08 2
1000-05S 0.16 1
1000-10T 0.16 2
1000-10S 0.32 1
1000-15T 0.24 2
1000-15S 0.48 1

1000 Type The main technical parameters

Max Presssure Mpa  Inlet size  Outlet size  Working chip size (mm) Install hole distance (mm) Install thread Length A  Outlet Pipe dia  (mm)  Working temperature: 
25Mpa  M10*1  /NPT 1/8  M10*1  /NPT 1/8 54*32*14 18 3-M5 A=32+N*14 Standard 6mm  -20°C to +60°C
N Chip number 

Max work pressure:25MPa

Delivery:0.08ml/cyc ~ 0.48ml/cyc
Lubricant viscosity (under standard temperature): oil≥N68,grease:NLGI 000#~2# Work temperature:-20°C~+60°C
Max work frequency (with stem):60cyc/min Max work frequency (without stem):200cyc/min Manifold number:3~8
Tubing: Outlet: Φ6mm length: 0.5~2.5m ,Inlet: Φ6mm length:1.2~3.5m

2000 Metering Devices

Working chips  Standard flow ML/CYC Each chip outlet quantity  
2000-10T 0.16 2
2000-10S 0.32 1
2000-15T 0.24 2
2000-15S 0.48 1
2000-20T 0.32 2
2000-20S 0.64 1
2000-25T 0.40  2
2000-25S 0.80  1
2000-30T 0.48 2
2000-30S 0.96 1
2000-35T 0.56 2
2000-35S 1.12 1

2000 Type The main technical parameters

Max Presssure Mpa  Inlet size  Outlet size  Working chip size (mm) Install hole distance (mm) Install thread Length A  Outlet Pipe dia  (mm)  Working temperature: 
25Mpa  M12*1 .25  M10*1  /NPT 1/8 80*45*19 32 4-M6 A=43+N*20.5 Standard 6mm  -20°C to +60°C
N Chip number 

Max work pressure:25MPa
Delivery:0.16ml/cyc ~ 1.12ml/cyc
Lubricant viscosity (under standard temperature) : oil ≥ N68, grease: NLGI 000#~2# Work temperature: -20°C~+60°C
Max work frequency (with stem): 60cyc/min Max work frequency (without stem): 200cyc/min Manifold number: 3~10
Tubing: Outlet: Φ6mm length: 1.2~3.5m
Inlet: Φ8mm length:1.5~4.5m Manifold Material: carbon steel

3000 Metering Devices

Working chips  Standard flow ML/CYC Each chip outlet quantity  
3000-25T 0.4 2
3000-25S 0.8 1
3000-50T 0.8 2
3000-50S 1.6 1
3000-75T 1.2 2
3000-75S 2.4 1
3000-100T 1.60  2
3000-100S 3.20  1
3000-125T 2 2
3000-125S 4 1
3000-150T 2.4 2
3000-150S 4.8 1

3000 Type The main technical parameters

Max Presssure Mpa  Inlet size  Outlet size  Working chip size (mm) Install hole distance (mm) Install thread Length A  Outlet Pipe dia  (mm)  Working temperature: 
25Mpa  Rp3/8  Rp1/4 128*70*28 47.6 4-M8 A=57.4+N*28.8 Standard 8mm  -20°C to +60°C
N Chip number 

Max work pressure:25MPa
Delivery:0.4ml/cyc ~ 4.8ml/cyc
Lubricant viscosity (under standard temperature) : oil ≥ N68, grease: NLGI 000#~2# Work temperature: -20°C~+60°C
Max work frequency (with stem): 60cyc/min Max work frequency (without stem): 200cyc/min Manifold number: 3~10
Tubing: Outlet: Φ8mm length: 1.5~4.5m
Inlet: Φ10mm length:1.8~5.5m Manifold Material: carbon steel


  • Previous:
  • Next:

  • Write your message here and send it to us